96 Roadmaster wagon partout!

Some of you may remember when I bought this thing last December and I dubbed it the rustmaster.
It's time to part this one out and everything is for sale except the transmission and the wiring for the climate control (my Fleetwood does not seem too happy with the 94 trans I stuck it with ) Car is a DGGM WB4, 150k, cloth tan interior, posi rear. Frame and quarters are junk, engine runs great, interior is in good shape, rear doors are good. Rear door panels are in great shape.

The following parts are sold or unavailable:
Sail panels
Front bumper
Transmission
Hitch
Front seats
Tail lights
Headliner
Front wheel wells are rotted

if only the grill wasnt busted

David is it still on the road? Only asking because of the plates. And where are you exactly?

1993 Roady-man wrote:

David is it still on the road? Only asking because of the plates. And where are you exactly?

Car is still registered to Lynol, but its at my house in CT (near Bridgeport). The exhaust is falling apart and getting louder by the day

'96 belt trim attaches differently from '92 belt trim correct? if I'm wrong then i might be interested in the passenger side rear quarter belt trim.

hows the right front fender?

Cool well if the fender is good and Pat needs it I can pick it up for him because I am going to make plans to come see you. I have to go over to philly and pick up my other parts too.

benn wrote:

'96 belt trim attaches differently from '92 belt trim correct? if I'm wrong then i might be interested in the passenger side rear quarter belt trim.

I think its the same but there is no black trim on the car. That is all electrical tape

buickestate wrote:

hows the right front fender?

Fender looks good and is solid. Small dent and a few scratches on it. $40

1993 Roady-man wrote:

Cool well if the fender is good and Pat needs it I can pick it up for him because I am going to make plans to come see you. I have to go over to philly and pick up my other parts too.

Cool. If its any easier for you I can bring the parts to NJ and leave them with Lynol (he's in Keyport NJ, about an hour from Philly).

benn wrote:

'96 belt trim attaches differently from '92 belt trim correct? if I'm wrong then i might be interested in the passenger side rear quarter belt trim.

95BRMW wrote:

I think its the same but there is no black trim on the car. That is all electrical tape

that's fine, i don't care much for the black trim anyway. as long as my stock fasteners will work. can anyone confirm that?

-ben

All the RMWs attach the trim the same. Only the RMS has different trim in 96.

Interested in the rear driver rear door upper f'glasss panel above door line. ( sent pm regarding sale).
Also, anybody ever removed this panel, or have a clue as to how to remove it?
I know it has 3 pins that slip into squeeze clips within door frame.

I'm in New City, NY... Near TZ bridge.
Hotrodder
Mitch

There is a phillips screw at the top, and an 11mm nut at the bottom. You will have to pull/pry gently to remove it. The pins will pull out of the trim, and can be reglued to the trim after removal from the clips. You will also encounter black goo on the back side of the trim, and two tapered shims. The part is made from injection molded PPE.

Many thanks Fred!!!

I assume that you mean to get to the screw and nut from the inside, removing the window trim?

Now to obtain new part.
Mitch

I did not see any on the outside, so you have deduced the correct answer, but the screw and nut should be accessible without removing any interior trim.

The part is getting harder to find. You should get one, and keep an extra one for a spare just in case.

Reassembly should be done with windshield urethane, then it becomes permanent.

the problem with these panels is they were glued with a foam that deteriorates over time. I have lost two on cars that were never repainted. It'd be worth it to just remove, clean and reapply them as they are becoming like hen's teeth to find them.

At some point, I'd guess someone will step up and make a mold and start to reproduce them....but our cars haven't achieved 'collectible' status yet...

David I will take the tail lights, headliner, and front seats. Now we need to try and get everyone on the same page with my other parts. PM sent Thanks again.

How much for the rear passenger side fly away panel?

Chris

Updated with parts that are sold. Sail panels were the first to sell Chris.
Best way to get a hold of me is a PM

Hello, interested in the driver side rear view mirror(if it's heated and power!) also I need the power window switch from the front passenger door...i'd take the entire switch panel if necessary. Reach me with availability and prices at dnvrdisc@msn.com Thank you,
Bob

^^^Look up Fred.
He'll hook you up.

Email sent.

Shell is gone, still have a bunch of parts off it.

I would be interested in chromed beltline mouldings that are GOOD. Also interior door panels that are NICE.