| 1996 RMW Woodgrain Side Moldings End Caps | |
|
|
Author | Message |
---|
theamcguy
Posts : 70 Join date : 2010-03-31 Age : 71 Location : Fayetteville, NC
| Subject: 1996 RMW Woodgrain Side Moldings End Caps Sat Dec 15, 2012 8:59 am | |
| I need two of the plastic end caps for the left side moldings 1996 RMW, front fender and door. Would be willing to buy a bent molding just for the end caps. Can anybody help? TIA | |
|
| |
Fred Kiehl
Posts : 7290 Join date : 2009-11-13 Age : 76 Location : Largo, FL 33774
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sat Dec 15, 2012 11:56 pm | |
| I may have the trim pieces. I will check Sunday. | |
|
| |
theamcguy
Posts : 70 Join date : 2010-03-31 Age : 71 Location : Fayetteville, NC
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Dec 16, 2012 4:00 pm | |
| | |
|
| |
Fred Kiehl
Posts : 7290 Join date : 2009-11-13 Age : 76 Location : Largo, FL 33774
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Dec 16, 2012 7:35 pm | |
| I have the fender piece in undamaged condition but the wood grain is peeling. The door piece i have is from a 94, and is a short one with the end that you want. I would like $25 for both, but shipping is high for the full length piece. I would consider cutting the fender piece if you want cheap shipping. Shipping for the full length piece is $18. Shipping for the small piece, and end of the long one is about $6. | |
|
| |
theamcguy
Posts : 70 Join date : 2010-03-31 Age : 71 Location : Fayetteville, NC
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Dec 16, 2012 7:43 pm | |
| Fred, thank you. I believe the end caps are just crimped on and if they are easy to remove that would be an option. No problem on the $25 and the cheapest shipping. | |
|
| |
Fred Kiehl
Posts : 7290 Join date : 2009-11-13 Age : 76 Location : Largo, FL 33774
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Dec 16, 2012 8:03 pm | |
| You may paypal a personal gift to jfkiehl@ij.net. Send your address separately, because paypal does not send it with personal functions. Shipping for the ends is only $3.50 | |
|
| |
theamcguy
Posts : 70 Join date : 2010-03-31 Age : 71 Location : Fayetteville, NC
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Dec 16, 2012 8:14 pm | |
| OK will get this out tomorrow. Thank you for your help. | |
|
| |
theblurrrr
Posts : 45 Join date : 2012-10-30 Location : Olympia, WA
| Subject: Woodgrain trim ends needed-93RMW Sun Jul 28, 2013 8:03 pm | |
| I'm doing the same trim repaint that others have done with the Rust-Oleum "sand" color--but I need to replace the trim endcap/studs that come on the ends of some of the upper trim pieces. I'm looking for one each of the pieces marked with the numbers below:
18420A - end/stud crimped at rear edge of 12504225 (RF fender upper trim) 18415A - connector/stud, LF fender between 12504226 and 12504228 "C" trim (crimped to front of 12504226) 18442A - end/stud crimped at front end of 12504989 (LF door upper trim, behind mirror) 18443A - end/stud crimped at rear end of 12504987 (LF door upper trim, in front of mirror) 18440A - end/stud crimped at front end of 12504986 (RF door upper trim, in front of mirror)
18432A - the gray stud in the front fender "C" trim forward of the wheel well.
I'll buy the whole molding piece if necessary or easier for seller, especially 12504986 and 12504987. "Woodgrain" finish NOT necessary since I intend repaint anyway. If you have damaged trim pieces with good end/studs, that's OK, I'm just looking for the intact end pieces.
I'm also looking for one of the rear cargo area net upper anchors as well--any color OK.
Thanks in advance!! | |
|
| |
silverfox103 Moderator
Posts : 3371 Join date : 2008-11-05 Age : 75 Location : Littleton, NH & St. Simons, GA
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Sun Jul 28, 2013 8:15 pm | |
| Get in touch with Fred K., he may be able to help you.
Tom | |
|
| |
Fred Kiehl
Posts : 7290 Join date : 2009-11-13 Age : 76 Location : Largo, FL 33774
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps Mon Jul 29, 2013 1:34 am | |
| I have a box of woodgrain trim. I will sell it all for $50 shipped. The parts have good ends on them. I do not know exactly what parts I have. | |
|
| |
Sponsored content
| Subject: Re: 1996 RMW Woodgrain Side Moldings End Caps | |
| |
|
| |
| 1996 RMW Woodgrain Side Moldings End Caps | |
|